Tennant 5400 Service Manual Download Page 75 | Manualshive

Page: 75 / 163

background image

ELECTRICAL

4-5

5400 330735 (3–01)

Measuring the specific gravity using a hydrometer
is a way to determine the charge level, and
condition of the batteries. If one or more of the
battery cells test lower than the other battery cells
(0.050 or more), the cell is damaged, shorted, or
is about to fail.

NOTE: Do not take readings immediately after
adding distilled water. If the water and acid are not
thoroughly mixed, the readings may not be
accurate. Check the hydrometer readings against
the following chart to determine the remaining
battery charge level:

SPECIFIC GRAVITY

BATTERY

at 27

C (80

F)

CHARGE

1.265

100% Charged

1.223

75% Charged

1.185

50% Charged

1.148

25% Charged

1.110

Discharged

NOTE: If the readings are taken when the battery
electrolyte is any temperature other than 27

C

(80

F), the reading must be temperature

corrected. Add or subtract to the specific gravity
reading 0.004, 4 points, for each 6

C (10

F)

above or below 27

C (80

F).

«
...
73
74
75
76
77
...
»

Summary of Contents for 5400




































































































































































Reviews:

No comments

Related manuals for 5400

Brand: Canon Pages: 100

Brand: Canon Pages: 124

Brand: Canon Pages: 203

Brand: Canon Pages: 28

Brand: GateWay Fax Systems Pages: 13

Brand: Janome Pages: 82

Brand: Happy Pages: 9

Brand: Digital Finishing Group Pages: 6

RIP-R-STRIPPER FCS16

Brand: General Equipment Pages: 63

Brand: Toyota Pages: 48

Brand: Briteq Pages: 8

CONTOUR 350 DELUXE

Brand: H. Winter Pages: 23

Brand: Sinbo Pages: 48

Brand: T-COM Pages: 6

Brand: Encore Pages: 28

hammerhead 1100srx

Brand: Bortek Pages: 74

Brand: Oki Pages: 653

Brand: ISM Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands