Tennant 5400 Service Manual Download Page 20

Page: 20 / 163

CHASSIS

2-6

5400 330735 (3–01)

TO INSTALL THE TRANSAXLE

1. Position the new transaxle under the

machine frame. Make sure the drive motor
electric lead is positioned on the left hand
side of the machine.

2. Lift the transaxle up into the machine frame

until the mount brackets and M8 hex screws
can be reinstalled. Tighten to 18 – 24 Nm
(15 – 20 ft lb).

3. Plug the drive motor into the main harness.

See schematic in the ELECTRICAL section
of this manual.

4. Reinstall the drive wheels onto the transaxle

using the four 0.250 in. hex nuts and
washers. Tighten to 11 – 14 Nm
(7 – 10 ft lb).

5. Remove the jack stands and lower the

machine to the ground.

6. Raise the scrubber head.

7. Operate the machine, checking for proper

operation of the transaxle.

Summary of Contents for 5400




































































































































































Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands

Tennant 5400, Service Manual

Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands