Tennant 5400 Service Manual Download Page 125

Page: 125 / 163

ELECTRICAL

4-55

5400 330735 (3–01)

ELECTRIC MOTORS

The carbon brushes on the vacuum fan motor,
scrub brush motor, and propelling motor should be
inspected after every 400 hours of machine
operation.

TO REPLACE VACUUM FAN MOTOR
BRUSHES

FOR SAFETY: Before Leaving Or Servicing
Machine; Stop On Level Surface, Turn Off
Machine.

1. Remove the vacuum fan from the machine.

See TO REMOVE VACUUM FAN
instructions in this section.

2. Pry back the locking tabs and remove the

fan motor cover.

NOTE : DO NOT operate vacuum fan with the top
cover removed.

3. Remove the two pan head screws holding

the clamp and motor brushes in place.
Remove the brushes and measure.
NOTE: If the motor brushes measure 10 mm
(0.375 in.) of an inch or less in length, install
new brushes.

Summary of Contents for 5400




































































































































































Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands

Tennant 5400, Service Manual

Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands