Tennant 5400 Service Manual Download Page 110

Page: 110 / 163

ELECTRICAL

4-40

5400 330735 (3–01)

16. Tighten the belt adjustment bolt. Tension the

belt by applying 2.5–2.7 lbs of force per belt
at the middle of the span that is opposite the
belt travel with a deflection of 0.10 inch.

17. Spin the brush drive plug to align the motor

sprocket with the lower drive sprocket.
Tighten the motor sprocket set screws.
Make sure to apply blue loctite 242 to the
set screws before installing.

18. Tighten the two pivot bolts to 18 – 24 Nm

(15 – 20 ft lb). Re–check the belt tension.

19. Reconnect the brush motor wires to the new

brush motor. See schematic in this section.
Make sure to reinstall the washers on the
terminal studs on the motor and the rubber
boots on the wires.

Summary of Contents for 5400




































































































































































Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands

Tennant 5400, Service Manual

Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands