Tennant 5400 Service Manual Download Page 90

Page: 90 / 163

ELECTRICAL

4-20

5400 330735 (3–01)

TO REPLACE 24 VOLT CONTACTOR

FOR SAFETY: Before Leaving Or Servicing
Machine; Stop On Level Surface, Turn Off
Machine.

1. Open the instrument panel. See TO

ACCESS INSTRUMENT PANEL
instructions.

FOR SAFETY: Disconnect the battery
connections before working on the machine.

2. Locate the contactor at the bottom edge of

the instrument panel box.

3. Mark and disconnect the wires leading to the

contactor. Note the direction of the line
side of diode. Make sure the line side is
connected to wire 22YEL. Failure to do
so will result in a short circuit.

4. Remove the two hex nuts holding the

contactor to the panel. Remove the
contactor from the instrument panel.

5. Install the new contactor onto the instrument

panel. Install the two nuts and hand tighten
tight.

6. Reconnect the wires to the contactor. See

electrical schematic in this section. DO NOT
over tighten the wire connections on the
contactor posts or damage may occur.

7. Reinstall the instrument panel. See TO

ACCESS INSTRUMENT PANEL
instructions.

8. Operate the machine. Check the vacuum

fan for proper operation.

Summary of Contents for 5400




































































































































































Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands

Tennant 5400, Service Manual

Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands