Tennant 5400 Service Manual Download Page 51

Page: 51 / 163

SCRUBBING

3-27

5400 330735 (3–01)

4. Loosen the M8 hex nut on the belt tension

bolt under the motor. Turn the tension bolt
down far enough to allow the belt to be
slipped off the motor pulley. Push the drive
belt down toward the drive plug in the brush
area.

NOTE: Make sure the scrub head is in the raised

position before attempting to remove the drive

plug rubber seal.

5. Using a needle nose pliers, pull the rubber

seal off the brush drive plug. Remove the
belt cover from the bottom of the scrub
head. Take care not to damage the cover
gasket.

6. Pull the drive belt off the bottom drive pulley.

7. Slip the new drive belt over the drive plug.

Push the rest of the belt up to the drive
motor and onto the motor drive pulley.

Summary of Contents for 5400




































































































































































Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands

Tennant 5400, Service Manual

Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands