Tennant 5400 Service Manual Download Page 66

Page: 66 / 163

SCRUBBING

3-42

5400 330735 (3–01)

4. Remove the clevis from the bottom end of

the cable.

Note the amount of threads the clevis is turned
onto the existing lift cable. Install the clevis onto
the new cable in the same location.

5. Loosen the jam nut holding the squeegee lift

cable to the ball joint. Un–screw the cable
from the ball joint.

6. Pull the cable end through the cable

bushing. Remove the cable from the
machine.

Remove the balljoint end and jam nut from the
existing cable. Install the jam nut and balljoint in
the same location on the new lift cable.

NOTE: Reverse this order to install the squeegee
lift cable.

7. Operate the machine. Check the squeegee

lift cable for proper operation.

Summary of Contents for 5400




































































































































































Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands

Tennant 5400, Service Manual

Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands