Tennant 5400 Service Manual Download Page 122

Page: 122 / 163

ELECTRICAL

4-52

5400 330735 (3–01)

3. Loosen the worm drive clamp on the small

outlet hose on the ES

pump. Remove the

hose.

4. Remove the ES

pump from the tank by

un–screwing it counter–clockwise.

5. Put water proof thread sealant on the

threads of the new ES

pump.

6. Screw the new pump clockwise into the

recovery tank. Tighten until the outlet tube
points towards the back of the machine.

7. Re–connect the small water line and worm

drive clamp to the ES

pump.

8. Re–connect the main wire harness to the

new pump. See schematic in the
ELECTRICAL section of this manual.

9. Close the recovery tank, operate the

machine and check the ES

pump for

proper operation.

Summary of Contents for 5400




































































































































































Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands

Tennant 5400, Service Manual

Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands