Tektronix RFM150, Instruction Manual

Page: 39 / 278

Tutorial
RFM 150 Instruction Manual 1–17
If it is not correct, turn the knob to highlight the desired site name
from the displayed list, then press F1 for MAKE ACTIVE.
If you require a new site name, press F2 to select NEW SITE.
Turn the knob to highlight each desired letter on screen, pressing
ENTER after each letter. Numbers can also be entered, using the
numeric keyboard. When the new site name appears as desired,
press F4 to select ACCEPT ENTRY. Now press F1 to make it
active.
2. Press STORE, then press F4 to select SET TEMP. The tempera-
ture and temperature units will be displayed. If they are correct,
proceed to step 3. If they are not correct, use the knob or keypad
to enter the current ambient temperature. Keypad entries must be
followed by pressing ENTER; partial keypad entries can be
cancelled by backspacing.
3. Press SEQ to enter the sequence menu. All sequences stored in
the instrument will be displayed. Turn the knob, if necessary, to
select the 24 hour sequence.
4. Press F1 (EXEC). The execute sequence menu will appear, with
the name of the selected sequence displayed at the top of the
screen.
(The 24 hour test is always set to start NOW and to repeat 4
times, in 6 hour intervals.)
5. Press F1 for START SEQ. An All Channel measurement will
occur, measuring levels for all channels that are in the active
channel table, except those that have been set to skip. When the
measurement is completed, the screen will go blank.
(In normal use, the instrument is left alone to repeat the test four
times. For this procedure, however, we will interrupt the test and
view the results of the initial measurement.)
6. Press the POWER key. A confirmation screen will appear. Press
F1 to abort.
7. Press the STORE key, then press F2 to select RSLTS MENU. Use
the knob to select the result of the test you just executed. You can
recognize it by the date and time, and because the TYPE will be
SEQUENCE.
Tutorial
RFM 150 Instruction Manual 1–17
If it is not correct, turn the knob to highlight the desired site name
from the displayed list, then press F1 for MAKE ACTIVE.
If you require a new site name, press F2 to select NEW SITE.
Turn the knob to highlight each desired letter on screen, pressing
ENTER after each letter. Numbers can also be entered, using the
numeric keyboard. When the new site name appears as desired,
press F4 to select ACCEPT ENTRY. Now press F1 to make it
active.
2. Press STORE, then press F4 to select SET TEMP. The tempera-
ture and temperature units will be displayed. If they are correct,
proceed to step 3. If they are not correct, use the knob or keypad
to enter the current ambient temperature. Keypad entries must be
followed by pressing ENTER; partial keypad entries can be
cancelled by backspacing.
3. Press SEQ to enter the sequence menu. All sequences stored in
the instrument will be displayed. Turn the knob, if necessary, to
select the 24 hour sequence.
4. Press F1 (EXEC). The execute sequence menu will appear, with
the name of the selected sequence displayed at the top of the
screen.
(The 24 hour test is always set to start NOW and to repeat 4
times, in 6 hour intervals.)
5. Press F1 for START SEQ. An All Channel measurement will
occur, measuring levels for all channels that are in the active
channel table, except those that have been set to skip. When the
measurement is completed, the screen will go blank.
(In normal use, the instrument is left alone to repeat the test four
times. For this procedure, however, we will interrupt the test and
view the results of the initial measurement.)
6. Press the POWER key. A confirmation screen will appear. Press
F1 to abort.
7. Press the STORE key, then press F2 to select RSLTS MENU. Use
the knob to select the result of the test you just executed. You can
recognize it by the date and time, and because the TYPE will be
SEQUENCE.