Tektronix DPO2304SX Printable Help Download | Manualshive

Page: 828 / 920

background image

Behavior. Measurements are updated approximately three times a second, or less for long record lengths. Measurements are
calculated after each acquisition. You can display up to eight automatic measurements.

TIP. Select the individual measurements directly from the Measure menu Histogram Measurements submenu.

What do you want to do next?

Learn about taking amplitude measurements.

Learn about taking timing measurements.

Learn about other measurements.

Learn about communications measurements.

Learn more about the Measurements list.

Learn more about the Measurement controls.

Waveform count

Displays the number of waveforms that have contributed to the histogram.

Hits in Box

Displays the number of points in or on the histogram box.

Peak Hits

Displays the number of points in the largest bin of the histogram.

Median

The middle point of the histogram box. Half of all acquired points within or on the histogram box are less than this value and half
are greater than this value.

Histogram Max

Displays the voltage of the highest nonzero bin in vertical histograms or the time of the rightmost nonzero bin in the horizontal
histograms.

Histogram Min

Displays the voltage of the lowest nonzero bin in vertical histograms or the time of the leftmost nonzero bin in the horizontal
histograms.

Pk-Pk

Displays the peak-to-peak value of the histogram.

■

Vertical histograms display the "voltage" of the highest nonzero bin minus the "voltage" of the lowest nonzero bin.

■

Horizontal histograms display the "time" of the rightmost nonzero bin minus the "time" of the leftmost nonzero bin.

Histogram Mean

Measures the average of all acquired points within or on the histogram box.

StdDev (standard deviation)

The standard deviation (Root Mean Square (RMS) deviation) of all acquired points within or on the histogram box.

Mean±1 StdDev

The percentage of points in the histogram that are within one standard deviation of the histogram mean.

Oscilloscope reference

796

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

«
...
826
827
828
829
830
...
»

Summary of Contents for DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DPO2304SX

Brand: ZOLL Pages: 5

Brand: Accu-Chek Pages: 3

Brand: iBin Pages: 2

Brand: Quadro Pages: 11

Brand: LAWO Pages: 459

Brand: earline Pages: 13

Brand: Hagie Pages: 141

Brand: Jacto Pages: 12

Brand: R&S Pages: 371

Brand: R.M. Young Pages: 9

Brand: L-Acoustics Pages: 5

Monkey Jump MM00125

Brand: M&M Pages: 2

Brand: GE Pages: 176

Brand: Triton Blue Pages: 11

Brand: MacDon Pages: 238

Brand: Harris Pages: 21

BIO-FIGHTER 4Xtreme

Brand: Dust Free Pages: 8

Brand: HF Scientific Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands