Tektronix DPO2304SX Printable Help Download

Page: 394 / 920

Set up parallel search parameters

After setting up a parallel bus, go to the Analyze menu, select Search, and then select the Bus trigger type; then open the
Configure tab.

Overview

Use the controls to set up the Parallel Bus parameters.

To use

For information on the controls, click the buttons.

■

■

■

■

■

Search / Mark Controls

Behavior

Clicking an entry in the Type column activates the individual search controls, similar to the one shown above. These controls vary
depending on the search Type. Setting the search conditions is similar to setting the parameters for an

Event Trigger

NOTE. No information will be displayed in this window until you specify at least one search Type in the

Search Select Control

Window

Analyzing waveforms

362

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

Summary of Contents for DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for DPO2304SX

Reviews:

Related manuals for DPO2304SX

Brands by name

Popular brands

Tektronix DPO2304SX, Printable Help

Search results

Summary of Contents for DPO2304SX

Reviews:

Related manuals for DPO2304SX

Brands by name

Popular brands