Tektronix DPO2304SX Printable Help Download Page 726

Page: 726 / 920

Negative overshoot. Amplitude (voltage) measurement.

Note that this value should never be negative (unless High or Low are set out-of-range).

Negative width. Timing measurement. The distance (time) between MidRef (default = 50%) amplitude points of a negative
pulse.

If MCross1Polarity = –

then

NegativeWidth = (MCross2 – MCross1)

else

NegativeWidth = (MCross3 – MCross2)

Waveform[Start]

Optical power. See

Mean dBm

Peak to peak. Amplitude measurement. The absolute difference between the maximum and minimum amplitude.

PeaktoPeak = Max – Min

Period. Timing measurement. Time taken for one complete signal cycle. The reciprocal of frequency. Measured in seconds.

Period = MCross3 – MCross1

Oscilloscope reference

694

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

Summary of Contents for DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for DPO2304SX

Reviews:

Related manuals for DPO2304SX

Brands by name

Popular brands

Tektronix DPO2304SX, Printable Help

Search results

Summary of Contents for DPO2304SX

Reviews:

Related manuals for DPO2304SX

Brands by name

Popular brands