manualshive.com logo in svg

SYRUNS SY5000 series, User Manual, Page: 17 / 115

Share
Download
SYRUNS SY5000 series User Manual Download Page 17

User Manual of SY5000 series AC Drive                                                            Installation

~15~

2.3.2 Ambient temperature

        To improve operation reality of AC Drive, please install in well-ventilated place. 
When used in an enclosed cabinet, install the cooling fan or cooling air-conditioning, 
and keep the environment temperature below 40

°

C.

2.3.3 Precaution

      Please put a dust cover on the AC Drive when install. Do not fall metal framents 
into AC Drive internal when drill holes. Please remove dust cover after installation 

finishes.

2.3.4 Installation direction and space

Figure 2- Installation direction and space of SY5000 series AC Drive

      In order to get good effect of cooling cycle, must install the AC Drive in vertical 
direction. Please refer to Figure 2-.

*********************************************************************

Note: When install two AC Drives upper and lower, we should utilize isolating plate.
*********************************************************************

Summary of Contents for SY5000 series




















































































































Reviews:

No comments