manualshive.com logo in svg

SYRUNS SY5000 series, User Manual, Page: 16 / 115

Share
Download
SYRUNS SY5000 series User Manual Download Page 16

User Manual of SY5000 series AC Drive                                                            Installation

~14~

2.3 Requirements and management of installation site

2.3.1 Installation site:
         

The installation site should meet the following conditions:

 

Good indoor ventilation

 

Ambient temperature -10

°

C~40

°

C

 

Humidity less than 90%RH, without dew

 

Don’t install in the combustibles such as woods

 

Avoid direct sunlight

 

No combustible, explosive, corrosive gases and liquids

 

No ash dust, oil dust, floatable fibers and metal particles

 

strong installed base, no vibration

 

No electromagnetic interference

Caution

3. Please hold the bottom of AC Drive when carry it.
    Risk of feet injury if only holding the panel.

4. Please install in metal board and other nonflammable materials.
    Risk of fire if installing in flammable materials.

5. If install two or more AC Drives in the same cabinet, please set the cooling fan,    
    and keep the air temperature below 40

℃

.

    Risk of fire and other accidents if overheating.

1. In order to avoid being exposed and damaged, don’t use other methods to   

    disassembly and assembly keypad and panels.
2. Don’t directly install big panel with keypad in the AC Drive, otherwise, it will    
    bring poor contact.Please separately install big panel in the AC Drive, then    
    install keypad in the big panel.

Caution

Summary of Contents for SY5000 series




















































































































Reviews:

No comments