Steris P920011-649 Operator'S Manual Download Page 36 | Manualshive

Page: 36 / 168

background image

3-7

Component Identification

Operator Manual

920011-649

3.3 Control

IMPORTANT:

Become familiar with all control locations and functions

before operating the Reliance EPS (see Figure 3-5).

The Reliance EPS Processor is equipped with a microprocessor

control system. The control system monitors and automatically

controls all cycle operations and functions. The control system offers

three different modes: Operator, Supervisor and Service mode.

3.3.1 Operator Mode

The Operator mode section of the control panel is used to control the

main functions of the processor: power ON or OFF, cycle selection,

start, stop and abort cycles, and display status or FAULT messages.

NOTE: A description of the control panel symbols is available behind
the control panel cover.

•

POWER (ON/OFF)

toggle switch – press top portion to turn

power

ON

or bottom portion to turn power

OFF

.

•

UNLOCK

toggle switch – press to unlock door.

•

START

touch pad – press once to start a selected cycle.

•

STOP

touch pad – press once to stop/interrupt cycle in

progress.

•

ALARM REPLY

touch pad – press to stop intermittent alarm

buzzer and acknowledge the displayed

FAULT

messages.

•

SINGLE

endoscope processing cycle touch pad – press to

select the preprogrammed SINGLE cycle to process ONE

endoscope. Press once to use WASHING and High Level

Disinfection (HLD) phases; press a second time to process HLD

phase only.

•

DOUBLE

endoscope processing cycle touch pad – press to

select the preprogrammed DOUBLE cycle to process TWO

endoscopes. Press once to use WASHING and HLD phases;

press a second time to process HLD phase only.

NOTE: The choice of selecting the WASHING phase is available
only if WASHING SELECT is set to YES  in Supervisor mode. If
WASHING  SELECT  is  set  to  NO,  pressing  the  touch  pad  a
second  time  will  have  no  effect  and  cycle  will  always  process
WASHING  and  HLD  phases  (refer  to  S

).

•

DECONTAM

cycle touch pad – press repeatedly to toggle

between the standard preprogrammed D-SHORT and D-LONG

cycles.

CAUTION

–

POSSIBLE EQUIPMENT

DAMAGE:

Use a soft damp

cloth and a mild detergent to
clean control panel touch
pads. Splashing water or any
other liquid will damage
control panel touch pads.

«
...
34
35
36
37
38
...
»

Summary of Contents for P920011-649









































































































































































Reviews:

No comments

Related manuals for P920011-649

Brand: FJC Pages: 2

Brand: Xoop Lighting Pages: 20

Brand: Vari Lite Pages: 132

Brand: Faderfox Pages: 8

Brand: laerdal Pages: 8

Brand: LAHTI PRO Pages: 16

Brand: laerdal Pages: 32

Brand: laerdal Pages: 32

Brand: laerdal Pages: 8

Brand: MagCore Pages: 80

Brand: MagCore Pages: 80

Brand: B&G Pages: 2

Pro hunter 2525

Brand: SprotDog Pages: 28

Brand: Barikell Pages: 32

Brand: BH FITNESS Pages: 24

Brand: Best Fitness Pages: 26

Water Inlet Suction Hose

Brand: Nilfisk-Advance Pages: 8

Brand: TRX Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands