Steris P920011-649 Operator'S Manual Download Page 110

Page: 110 / 168

5-9

Cycle and Control Value Programming

Operator Manual

920011-649

2. Press

SCROLL arrows

(up or down) until

MISCELLANEOUS

appears.

3. Press

ENTER

touch pad to confirm selection. Display shows:

__ blinking

4. Press

SCROLL arrows

(up or down) to scroll through available

languages for display messages and printouts.

5. Press

ENTER

touch pad to confirm selection. Display shows:

__ blinking

NOTE: Time format can be changed from AM/PM to 24 h in
Service mode by a qualified service technician. For instructions,
refer to S

ECTION

2, S

ERVICE

ODE

ROCEDURE

, of Maintenance

Manual (P764333-736).

6. Press

SCROLL arrows

(left or right) to set current time of day.

7. Press

ENTER

touch pad to confirm time setting. Display shows:

__ blinking

NOTE: Date format can be changed to MM-DD-YY, DD-MM-YY
or YY-MM-DD in Service mode by a qualified service technician.
For instructions, refer to S

ECTION

2, S

ERVICE

ODE

ROCEDURE

of Maintenance Manual (P764333-736).

8. Press

SCROLL arrows

(left or right) to set current date.

9. Press

ENTER

touch pad to confirm setting. Display shows:

__ blinking

NOTE: Concerning bar code reader accessory, note the following:

1) Bar code reader function cannot be enabled if bar code

reader (accessory) is not installed.

2) If bar code reader is present, refer to Bar Code Reader

Installation Instruction (P920011-654), included with bar code
reader, or S

ECTION

2, S

ERVICE

ODE

ROCEDURE

, of

Maintenance

Manual

(P764333-736),

for

complete

programming instructions and bar code lists templates.

LANGUAGE

ENGLISH

MISCELLANEOUS

TIME HH:MM

MISCELLANEOUS

DATE MM-DD-YY

BAR CODE READER

Summary of Contents for P920011-649









































































































































































Search results

Summary of Contents for P920011-649

Reviews:

Related manuals for P920011-649

Brands by name

Popular brands

Steris P920011-649, Operator'S Manual

Search results

Summary of Contents for P920011-649

Reviews:

Related manuals for P920011-649

Brands by name

Popular brands