Steris P920011-649 Operator'S Manual Download Page 41

Page: 41 / 168

3-12

920011-649

Operator Manual

Component Identification

3.7 Dual Pre-Filter and

Pressure Regulator

Assembly (Required

Accessory)

See Figure 3-8.

The Dual Pre-Filter and Pressure Regulator Assembly (required

accessory) is designed to help reduce the particulate and microbial

load on the final 0.2

μm bacterial-retentive filter. This required

accessory includes:

•

one multi-layer depth media filter cartridge.

•

one dual-layer absolute membrane filter cartridge.

•

one pressure regulator to reduce incoming water pressure to

310 kPa (45 psig).

•

one spanner wrench to easily remove and reinstall filter bowls for

maintenance (refer to Figure 6-6).

•

two manual ball shutoff valves.

•

pressure gauge.

•

Installation Instructions (920-500-287).

REF. 920-013-528

Pressure Regulator

From Building Hot Water Supply

Multi-Layer Depth Media

Filter Cartridge

Dual-Layer Absolute Membrane

Filter Cartridge

Manual Ball Valve

Figure 3-8. Dual Pre-Filter and Pressure Regulator Assembly (Required Accessory)

Manual Ball

Valve

Pressure Gauge

To Processor

Hot Water Inlet

Summary of Contents for P920011-649









































































































































































Search results

Summary of Contents for P920011-649

Reviews:

Related manuals for P920011-649

Brands by name

Popular brands

Steris P920011-649, Operator'S Manual

Search results

Summary of Contents for P920011-649

Reviews:

Related manuals for P920011-649

Brands by name

Popular brands