manualshive.com logo in svg

Sokkia iX-1001, Operator'S Manual, Page: 30 / 177

Share
Download
Sokkia iX-1001 Operator'S Manual Download Page 30

26

5. BASIC OPERATION

ii) Connection via RS232C cable

: RS232C is selected

: Sending data from a data collector to iX

:  Sending data from iX to a data collector

: Exchanging data in both directions between iX and a data collector

• A red arrow indicates that data transmission has failed and data needs to be sent again.

(7) Input mode icon

Selection of input mode 

"5.1 Basic Key Operation 

 Inputting letters/figures"

(8) Input panel icon

 "5.3 Inputting Characters using the Input Panel"

(9) PPM setting icon

Current atmospheric correction factor setting is displayed.
You can jump to the Atmos config. screen.

"19.4 Observation Conditions - Atmosphere"

(10) Internet communication status

Connection status of internet communication is displayed.
You can jump to the Internet config. screen.

"9.4 Wireless LAN Settings and Communication"

"9.5 Cellular Settings and Communication"

Configuration of internet communication.

Connection status to a router is displayed as follows.
i) Wireless LAN connection

: Disconnected/Intensity of signal less than -91 (dBm)

: Intensity of signal -90 to -70(dBm)

: Intensity of signal -71 to -68(dBm)

: Intensity of signal -67 to -58(dBm)

: Intensity of signal more than -57 (dBm)

ii) Cellular connection

: Connected

: Disconnected

_1

Inputting numbers and symbols

_a

Inputting lower case alphabetic characters

_A

Inputting upper case alphabetic characters

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments