Sokkia iX-1001 Operator'S Manual Download Page 91 | Manualshive

Page: 91 / 177

Sokkia iX-1001 Operator'S Manual Download Page 91

87

15. SETTING-OUT MEASUREMENT

PROCEDURE

1. Select "Setting out" in <Menu> to display <Setting

out>.

2. Set the instrument station and the backsight

station to define the reference direction. Select
"Occupy setup" in <Setting out>. Enter data for
the instrument station and press

[OK]

to move to

Backsight setup.



"13.1 Entering Instrument Station Data"

3. Set the azimuth angle for the backsight station.

Press

[OK]

to return to <Setting out>.



"13.2 Azimuth Angle Setting"

4. Select "SO data setting" in <Setting out>.

In the distance mode that conforms to your
measurement requirements, enter the included
angle between the reference point and the setting-
out point in "SO.H.ang", and the distance (slope
distance, horizontal distance or height difference)
from the instrument station to the position to be set
out in "SO.Sdist". Press

[OK]

to set the input

values.

«
...
89
90
91
92
93
...
»

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments