manualshive.com logo in svg

Sokkia iX-1001, Operator'S Manual, Page: 78 / 177

Share
Download
Sokkia iX-1001 Operator'S Manual Download Page 78

74

13. COORDINATE MEASUREMENT

2. Tap the screen title to display popup and select 

"Key in azimuth" display and enter the desired 
angle in "Azimuth".

•

[SRCH]

: Performs Auto Pointing. Rotates the 

instrument in the direction of the backsight.

•

[Azimuth] /[H.ANG]/[None]/[0 SET]

: Switches 

horizontal angle setting method.

 "



Horizontal angle settings"

3. Press 

[OK]

 to set the input values. <Coord. 

measurement> is displayed.  



Horizontal angle settings

Azimuth (set both horizontal and azimuth angles to the same value)/H.ang (input both horizontal and 
azimuth angles)/None (input azimuth angle only)/0 SET (horizontal angle set to 0

°

)

The coordinate values of the target can be found by measuring the target based on the settings of the 
instrument station and backsight station. 

The coordinate values of the target are calculated using the following formulae. 

N1 Coordinate = N0 + S x sinZ x cosAz
E1 Coordinate = E0 + S x sinZ x sinAz
Z1 Coordinate = Z0 + S x cosZ + ih - th

N0: Station point N coordinateS: Slope distance ih: Instrument height
E0: Station point E coordinateZ: Zenith angle th: Target height
Z0: Station point Z coordinateAz: Direction angle

"Null" coordinates will not be included in calculations. "Null" is not the same as zero. 

PROCEDURE

1. Sight the target at the target point.

13.3 3-D Coordinate Measurement

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments