Sokkia iX-1001 Operator'S Manual Download Page 82

Page: 82 / 177

14. RESECTION MEASUREMENT

5. Press

[YES]

to use the measurement results of

the first known point.

• You can also input target height here.
• Press

[NO]

to return to the screen in step 4 and

perform measurement again.

6. Repeat procedures 4 to 5 in the same way from

subsequent points.
When the minimum quantity of observation data
required for the calculation is present,

[CALC]

displayed.

[AUTO]

will be displayed for the 3rd point

onwards. Pressing

[AUTO]

will rotate the

instrument to the next point and start auto
measurement.

• Press

[

STOP

]

during auto measurement to

display a confirmation message. Press

[

YES

]

this message to return to the first point measured
using auto measurement. Measurement can now
be continued manually. Press

[

]

to continue

measurement manually from the current position.

Summary of Contents for iX-1001


















































































































































































Search results

Summary of Contents for iX-1001

Reviews:

Sokkia iX-1001, Operator'S Manual, Page: 82 / 177

Search results

Summary of Contents for iX-1001

Reviews: