manualshive.com logo in svg

Sokkia iX-1001, Operator'S Manual, Page: 142 / 177

Share
Download
Sokkia iX-1001 Operator'S Manual Download Page 142

138

21. CHECKS AND ADJUSTMENTS

If for whatever reason instrument error relating angle measurement occurs, this will adversely affect angle 
measurement. With this option you can measure collimation offset constant in your instrument so that the 
instrument can eliminate the angle error between Face 1 and 2. Perform the following procedures to correct 
the collimation offset constant.

• Perform adjustment in weak sunlight and no scintillation.

• It is recommended to perform collimation adjusting before the measurement especially when accurate result 

is desired in single face observations.

PROCEDURE Adjusting

1. Carefully level the instrument.

2. Install a target at a point about 100 m in the 

horizontal direction from the instrument.

3. Select "Inst. cons." in <Configuration>.

4. Select "Collimation".

21.4 Collimation

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments