manualshive.com logo in svg

Sokkia iX-1001, Operator'S Manual, Page: 51 / 177

Share
Download
Sokkia iX-1001 Operator'S Manual Download Page 51

47

9. CONNECTING TO EXTERNAL DEVICES

8. Press 

[Connect]

 in <Internet> to start 

communication.

A program installed on the instrument can now 
communicate with an external device.

• Press 

[Disconnect]

 to terminate the connection.

• When you can not access the internet after the 

series of steps for connection, check the Dial 
Number. If a wrong dial number is input, internet 
connection is not available.

Using USB port 2, the instrument and a computer can be communicated. There are USB mode and Mobile 
mode.

USB port

The instrument has two different USB ports. Each port is used for connection to different types of devices.

• TOPCON CORPORATION cannot guarantee that all USB devices are compatible with the iX USB ports.
• Use a computer WindowsVista/7 is based and USB connection is capable.
• Remove the USB cable from USB port 2 carefully to avoid damaging the cable.

9.6

Connecting via USB Cable

Port name

Device type

USB port 1

USB flash drive

USB port 2 (mini-B)

computers etc.

USB port 1

USB port 2 (mini-B)

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments