manualshive.com logo in svg

Sokkia iX-1001, Operator'S Manual, Page: 86 / 177

Share
Download
Sokkia iX-1001 Operator'S Manual Download Page 86

82

14. RESECTION MEASUREMENT

5. If measuring two or more known points, repeat 

procedures 4 in the same way from the second 
point.

6. Press 

[CALC]

 or 

[YES]

 to automatically start 

calculations after observations of all known points 
are completed.

• Instrument station elevation and standard 

deviation, which describes the measurement 
accuracy, are displayed in <Result>.

Standard deviation values for each point are 
displayed in <Detail>.

7. If there are problems with the results of a point, 

align the cursor with that point and press 

[OMIT]

.

 “OMIT” is displayed to the right of the point. 
Repeat for all results that include problems.

8. Press 

[RE CALC]

 to perform calculation again 

without the point designated in step 7 The result is 
displayed.
If there are no problems with the result, go to step 
9.
If problems with the result occur again, perform the 
resection measurement from step 4.

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments