Home
/
Sokkia
/
iX-1001
/
Operator'S Manual

Sokkia iX-1001, Operator'S Manual, Page: 125 / 177

Share

Page: 125 / 177

Sokkia iX-1001 Operator'S Manual Download Page 125

121

19. CHANGING THE SETTINGS

When a password has been set, the password screen will appear when the instrument is powered ON.
Setting a password allows you to protect important information such as measurement data.
No password was set when the instrument was shipped. When setting a password for the first time, leave the
"Old password" box blank.

Select "Inst. Config" in <Configuration> and select "Password".

Items set

Old password

: Input current password

New password

: Input the new password

New password again

: Input the new password again

• Password can be from 3 up to 16 characters in length. Input characters will be displayed as asterisks.
• To deactivate the password function, perform the new password setting procedure but enter a "space" in the

"New password" box.



• The password function will not be canceled when a cold boot is performed.
• The password must be input after powering ON the instrument from an external device when a password has

been set.

19.9 Instrument Conditions - Password

«
...
123
124
125
126
127
...
»

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments