manualshive.com logo in svg

Sokkia iX-1001, Operator'S Manual, Page: 123 / 177

Share
Download
Sokkia iX-1001 Operator'S Manual Download Page 123

119

19. CHANGING THE SETTINGS

Select "Inst. Config" in <Configuration> and select "Instrument".

Items set and options (*: Factory setting)

Illum. hold (

{

}

 function)

: Laser-pointer*/Guide light

Guide light brightness

: 1 to 3 (3*)

Guide pattern

: 1* (simultaneous)/2 (alternating)

Laser-pointer off 

: No/1 min./5 min.*/10 min./30 min.

V manual

: No*/Yes

Reticle lev 

: 0 to 5 level (3*)

Volume

: Off/1/2/3/4/5 (3*)

• "Reticle lev"

"19.5 Instrument Conditions - Display 

 Adjusting backlight brightness/turning the reticle illumination 

and key backlight ON/OFF"

• Setting "V manual" to "Yes"

"27.2 Manually Indexing the Vertical Circle by Face 1/2 Measurement"

Laser-pointer off

To save power, the laser-pointer is automatically turned off after the set time has elapsed.

19.7 Instrument Conditions - Instrument

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments