manualshive.com logo in svg

Sokkia iX-1001, Operator'S Manual, Page: 28 / 177

Share
Download
Sokkia iX-1001 Operator'S Manual Download Page 28

24

5. BASIC OPERATION

(2) Target type icon

Selection of target type and configuration of prism constant correction value.
You can jump to the Distance config. or Reflector config. screen.

"19.2 Observation Conditions - Dist"

"19.3 Observation Conditions - Reflector (Target)"

: Prism (0 mm)
:

 

360° prism (-7 mm)

: Sheet (0 mm)
: N-Prism
: "+" indicates a target used with an external device or in a program installed 
   in the Program mode.

(3) Motor icon

Configuration of Auto Pointing/Auto Tracking status. The display may change slightly depending on the 
target type selected. Auto Tracking items are only relevant to Auto Tracking models and are not available 
for Auto Pointing models.
You can jump to the Search/Track config. screen.

"10.1 Auto Pointing and Auto Tracking Settings"

: Perform Auto Pointing and Tracking when measuring the distance
: Perform only Auto Pointing when measuring the distance
: Measure the distance only
: Start Auto Tracking. "TRK Off" is displayed when performing Auto

  Tracking or when in "Prism wait" status. Tap to quit Auto Tracking.

: Begin searching
: Rotates the instrument 180°

One of the following icons will be displayed while the motor is in operation to indicate the current status of 
the instrument.

: Rotating

: Rotating at fixed velocity

: Searching/Searching after target lost during Auto Tracking

: Auto Tracking in progress

: Auto Tracking idle (when Auto Tracking set)

: Auto Tracking in predicted direction

: Waiting for prism during Auto Tracking

Predicted direction and waiting for prism: "10.1 Auto Pointing and Auto Tracking Settings 

 Lost Prism"

• Auto Tracking and Auto Pointing cannot be performed when "Reflectorless" has been selected as the 

target type (

 will be displayed). Auto Tracking cannot be performed when "Sheet" has been selected 

as the target type (

 will be displayed).

• An arrow indicating turn direction will be displayed when the instrument is rotating at a fixed velocity.

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments