manualshive.com logo in svg

Sokkia iX-1001, Operator'S Manual, Page: 43 / 177

Share
Download
Sokkia iX-1001 Operator'S Manual Download Page 43

39

9. CONNECTING TO EXTERNAL DEVICES

PROCEDURE Displaying 

Bluetooth

 information for the iX

1. Press 

[Info]

 in <

Bluetooth>

" to display information 

for the iX.

"9.1 Wireless Communication using Bluetooth 
Technology  PROCEDURE Setting for 
Bluetooth communication"

Register the 

Bluetooth

 address (BD ADDR) 

displayed here in the paired device set as 
"Master".

2. Press 

{Enter}

 to return to <

Bluetooth>.

 

Bluetooth

 device address

This is a number unique to one particular 

Bluetooth

 device used to identify devices during communication. 

This number consists of 12 characters (numbers 0 to 9 and letters from A to F).
Some devices may be referred to by their 

Bluetooth

 device address.

•

Bluetooth

 communication causes instrument battery power to be depleted at a rate higher than that for normal 

operation. 

• Check that the companion device (data collector, computer, or cellular phone etc.) is turned on and the 

relevant 

Bluetooth

 settings are complete.

•  All communication settings will be changed to factory settings when a cold boot is performed. Comms setup 

will need to be performed again.

"9.1 Wireless Communication using Bluetooth Technology"

PROCEDURE

1. Complete the necessary iX settings for 

Bluetooth

 

communication.

"9.1 Wireless Communication using Bluetooth 
Technology   PROCEDURE Setting for 
Bluetooth communication"

2. Start communication by the data collector.

Manual of the program mounted on the data 
collector

When a connection has been successfully 
established, is 

displayed.

3. Terminate the connection by the data collector.

9.2

Communication between the iX and Companion Device

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments