manualshive.com logo in svg

Sokkia iX-1001, Operator'S Manual, Page: 173 / 177

Share
Download
Sokkia iX-1001 Operator'S Manual Download Page 173

169

28. REGULATIONS

California 
and NY, 
U.S.A.

Recycling
Batteries

 Canada

ICES-Class A

This Class A digital apparatus meets all requirements of Canadian 
Interference-Causing Equipment Regulations.
Cet appareil numérique de la Class A respecte toutes les exigences du 
Règlement sur le matériel brouilleur du Canada.

This class A digital apparatus complies with Canadian ICES-003. 
Cet appareil numerique de la classe A est conforme a la norme NMB-003 
du Canada.

Operation is subject to the following two conditions: (1) this device may not 
cause interference, and (2) this device must accept any interference, 
including interference that may cause undesired operation of this device.
This equipment complies with IC radiation exposure limits set forth for an 
uncontrolled environment and meets the RSS-102 of the IC radio 
frequency (RF) Exposure Guidelines.

This equipment has very low levels of RF energy that it deemed to comply 
without maximum permissive exposure evaluation (MPE). But it is 
desirable that it should be installed and operated keeping the radiator at 
least 20cm or more away from person's body.

Region/

Country

Directives/ 

Regulations

Labels/Declarations

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments