Home
/
Sokkia
/
iX-1001
/
Operator'S Manual

Sokkia iX-1001, Operator'S Manual, Page: 109 / 177

Share

Page: 109 / 177

Sokkia iX-1001 Operator'S Manual Download Page 109

105

18.SURFACE AREA CALCULATION

You can calculate the area of land (slope area and horizontal area) enclosed by three or more known points on
a line by inputting the coordinates of the points

• Number of specified coordinate points: 3 or more, 30 or less
• It is possible to allocate Operating icons in measurement menus to suit various applications and the ways that

different operators handle the instrument.

"19.12 Allocating Operating Icons"



• An error will occur if only two points (or less) are entered when specifying an enclosed area.
• Be sure to observe points on an enclosed area in a clockwise or counterclockwise direction. For example, the

area specified by entering point numbers 1, 2, 3, 4, 5 or 5, 4, 3, 2, 1 implies the same shape. However, if
points are not entered in numerical order, the surface area will not be calculated correctly.



Slope area

The first three points specified are used to create the surface of the slope area. Subsequent points are
projected vertically onto this surface and the slope area calculated.

PROCEDURE Surface area calculation by measuring points

1. Select "Area calc." in <Menu>

Input

Output

Coordinates:

P1 (N1, E1, Z1)

Surface area:

S (horizontal area and slope area)

...
P5 (N5, E5, Z5)

«
...
107
108
109
110
111
...
»

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments