manualshive.com logo in svg

Sokkia iX-1001, Operator'S Manual, Page: 121 / 177

Share
Download
Sokkia iX-1001 Operator'S Manual Download Page 121

117

19. CHANGING THE SETTINGS

Adjusting backlight brightness/turning the reticle illumination and key backlight ON/OFF

Pressing 

{

}

 switches the brightness level of the backlight in conjunction with the ON/OFF status of the 

reticle illumination/key backlight. 
When the instrument is powered ON the brightness level is set to "Backlight (Normal)". "Backlight 
(Normal)" was set to a higher brightness level than "Backlight (Reticle ON)" when the instrument was 
shipped but these values can be modified according to user preferences.

• When "Backlight (Normal)" is set to "Auto" the instrument light sensor gauges the level of ambient 

brightness and automatically sets backlight brightness accordingly. Depending on ambient light 
conditions, performance of this function may be sub-optimal, or the display may flicker between 
brightness settings.

Backlight Off

To save power, the backlight will be turned off if the instrument is not operated for the selected time. 
However, the backlight will not be turned off when "Backlight (Reticle)" is selected.

Key backlight

The key backlight can be set to "ON" or "OFF". When "key backlight" is set to "ON", the key backlight is lit 
/OFF in conjunction with pressing 

{

}

.

Color setting

Set "Color" to "2" (monochrome) when strong sunlight reduces visibility of the display. When "Auto" is 
selected, the instrument detects the ambient brightness level and automatically sets the appropriate color 
setting accordingly.

"5.2 Display Functions"

• Do not block the instrument light sensor when "Color" is set to "Auto". The instrument will be unable to 

gauge ambient brightness and the display will flicker as a result.

Power-saving mode

When "Power-saving mode" is set to "ON", the display unit which is not operated is switched the light off 
to save power.

Backlight OFF

Backlight (Normal) 

brightness

{

}

Reticle backlight ON

{

}

Reticle backlight OFF

Time set in 

"Backlight Off" elapses

࣭

Key pressed

࣭

Touch panel operated

Backlight

Only when "Key 

backlight" set to "ON"

Power ON

(Reticle ON)

brightness

Key backlight ON

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments