Home
/
Sokkia
/
iX-1001
/
Operator'S Manual

Sokkia iX-1001, Operator'S Manual, Page: 118 / 177

Share

Page: 118 / 177

Sokkia iX-1001 Operator'S Manual Download Page 118

114

19. CHANGING THE SETTINGS

Select "Obs.condition" in <Configuration> and select "Atmos".

Items set and options (*: Factory setting)

Temperature

: -35 to 60°C (15*)/-22 to +140°F (59*) (When Dist.reso. is 1 mm)

Pressure

: 500 to 1400hPa (1013*)/375 to 1050mmHg (760*)/14.8 to 41.3

(inchHg) (29.9*) (When Dist.reso. is 1 mm)

Humidity input

: No (50%)*/Yes

Humidity

: 0 to 100 (%) (50*) (When Dist.reso. is 1 mm)

ppm (Atmospheric correction factor)



: -499 to 499 (0*) (When Dist.reso. is 1 mm)

•

[0ppm]

: Atmospheric correction factor returns to 0 and temperature and air pressure are set to the factory

settings.

• Atmospheric correction factor is calculated and set using the entered values of the temperature and air

pressure. Atmospheric correction factor can also be entered directly.

• The "Humidity" is displayed only when the "Humidity input" is set to "Yes".
• When 0.1 mm is selected in "Dist.reso", values can be input to the first decimal place.
• When the settings here are different between Basic mode and Program mode, Program mode settings are

prior for use.

19.4 Observation Conditions - Atmosphere

«
...
116
117
118
119
120
...
»

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments