Smartgen HGM 9310CAN Series User Manual Download Page 66

Page: 66 / 77

HGM93XX MPU(CAN) SERIES GENSET CONTROLLER

HGM93XX MPU(CAN) Series Genset Controller Version: 1.1 2016-11-03 Page 66 of 77

SMS
MANUAL
MODE

SMS MANUAL MODE OK

Set as manual mode

SMS AUTO
MODE

SMS AUTO MODE OK

Set as auto mode

SMS
DETAIL

Pass back information can
be set via controller
software.

Gets details information of genset.

SMS
INHIBIT
START

INHIBIT START OK

Generator start will be inhibited.

SMS
PERMIT
START

PERMIT START OK

Discharge the inhibit start signal.

NOTE:

Its national and area’s cods must be added. e.g. China: 8613666666666

NOTE:

When sending orders, users need to follow SMS orders in above form and all the

letters must be capital.

NOTE:

Pass back information from SMS DETAIL including: working mode, mains voltage,

generator voltage, load current, mains frequency, generator frequency, active power,

apparent power, power factor, battery voltage, D+ voltage, water temperature, oil pressure, oil

level, engine speed, total running time, genset status, and alarm status.

Summary of Contents for HGM 9310CAN Series














































































Search results

Summary of Contents for HGM 9310CAN Series

Reviews:

Related manuals for HGM 9310CAN Series

Brands by name

Popular brands

Smartgen HGM 9310CAN Series, User Manual

Search results

Summary of Contents for HGM 9310CAN Series

Reviews:

Related manuals for HGM 9310CAN Series

Brands by name

Popular brands