Smartgen HGM 9310CAN Series User Manual Download Page 52

Page: 52 / 77

HGM93XX MPU(CAN) SERIES GENSET CONTROLLER

HGM93XX MPU(CAN) Series Genset Controller Version: 1.1 2016-11-03 Page 52 of 77

193

Extend 1 Sensor 22 Low
Warn

194

Extend 1 Sensor 23
High Shut

195

Extend 1 Sensor 23
High Warn

196

Extend 1 Sensor 23 Low
Shut

197

Extend 1 Sensor 23 Low
Warn

198

Extend 1 Sensor 24
High Shut

199

Extend 1 Sensor 24
High Warn

200

Extend 1 Sensor 24 Low
Shut

201

Extend 1 Sensor 24 Low
Warn

201-
229

Reserved

230

Stop Mode

Action in stop mode.

231

Manual Mode

Action in Manual mode.

232

Reserved

233

Auto Mode

Action in Auto mode.

234

Generator On Load

235

Mains On Load

236

Reserved

237

Reserved

238

Reserved

239

Reserved

240-
279

PLC Flag1-40

280-
299

Reserved

8.2.1 CUSTOM PERIOD OUTPUT

Defined Period output is composed by 2 parts, period output S1 and condition output S2.

While S1 and S2 are

TRUE

synchronously, OUTPUT;

While S1 or S2 is

FALSE

, NOT OUTPUT.

Period output S1, can set generator’s one or more period output freely, can set the delayed

time and output time after enter into period.

Summary of Contents for HGM 9310CAN Series














































































Search results

Summary of Contents for HGM 9310CAN Series

Reviews:

Related manuals for HGM 9310CAN Series

Brands by name

Popular brands

Smartgen HGM 9310CAN Series, User Manual

Search results

Summary of Contents for HGM 9310CAN Series

Reviews:

Related manuals for HGM 9310CAN Series

Brands by name

Popular brands