Smartgen HGM 9310CAN Series User Manual Download Page 24

Page: 24 / 77

HGM93XX MPU(CAN) SERIES GENSET CONTROLLER

HGM93XX MPU(CAN) Series Genset Controller Version: 1.1 2016-11-03 Page 24 of 77

5.5 MANUAL START/STOP OPERATION

1. MANUAL START: Manual mode is selected by pressing the

button; a LED besides

the button will illuminate to confirm the operation; then press

button to start the

gen-set; can detect crank disconnect condition and generator accelerates to high-speed

running automatically. With high temperature, low oil pressure, over speed and abnormal

voltage during generator running, controller can protect genset to stop quickly. Press

(HGM9320MPU, HGM9320CAN) or

(HGM9310MPU, HGM9310CAN) can

control the switch to close or open. (please refer to No.4~9 of Automatic Start Sequence

for detail procedures; it is noted that the switch close/open ways are different)

2. MANUAL STOP: Press

can stop the running generators. (please refer to No.3~8

of Automatic Stop Sequence for detail procedures).

NOTE: In “manual mode”, the procedures of ATS please refer to

Switch Control

Procedure

of generator in this manual.

Summary of Contents for HGM 9310CAN Series














































































Search results

Summary of Contents for HGM 9310CAN Series

Reviews:

Related manuals for HGM 9310CAN Series

Brands by name

Popular brands

Smartgen HGM 9310CAN Series, User Manual

Search results

Summary of Contents for HGM 9310CAN Series

Reviews:

Related manuals for HGM 9310CAN Series

Brands by name

Popular brands