Skoda Octavia II 2004 Workshop Manual Download Page 61

Page: 61 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

– Open catch clamp -arrow- and disconnect plug.

– Release plug of antenna socket -arrows- and disconnect.
– Disconnect the plug for the mobile phone pre-installation

(A as of CW 22.11 with the GSM II mobile phone

pre-installation and mobile phone holder).

Installing
Installation is carried out in the reverse order. When installing,

observe the following:

Note

When inserting the navigation system on no account press on the

display or on the buttons otherwise they will be damaged.

– If the navigation system was replaced, an adaptation must be

performed by entering the safety code

⇒ page 48

and code

⇒ Vehicle diagnostic tester.

3.7

Self-diagnosis of the navigation system

Carry out “self-diagnosis” with the ⇒ Vehicle diagnostic tester in

the function “Targeted fault finding”.

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

3. Navigation system

Summary of Contents for Octavia II 2004












































































































































































































Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands

Skoda Octavia II 2004, Workshop Manual

Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands