Skoda Octavia II 2004 Workshop Manual Download Page 188

Page: 188 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

– Press off the catch pegs -arrows- and press the plug connec‐

tions out of the relay carrier.

Installing
Installation is carried out in the reverse order. When installing,

observe the following:
– Follow the work procedure when connecting the battery

⇒ page 2

1.3

Removing and installing additional relay

carrier above the onboard supply control

unit

Note

♦

The assignment of the relay carrier depends upon the vehicle

equipment.

♦

Exact assignment of the relay carrier ⇒ Current flow diagrams,

Electrical fault finding and Fitting locations.

Removing
– Disconnect battery earth strap

⇒ page 2

– Remove lower part of the dash panel insert on the driver's side

⇒ Body; Rep. gr. 70 Work.

– Pull the relay out of the relay carrier above the vehicle voltage

control unit.

– Slacken the plug connections -1- out of the catch pegs

-arrows- and press out of the relay carrier.

– Release the holder -arrow A- and remove together with the

fuse -arrow B- from the relay carrier.

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

180

Rep. gr.97 - Wiring

Summary of Contents for Octavia II 2004












































































































































































































Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands

Skoda Octavia II 2004, Workshop Manual

Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands