Skoda Octavia II 2004 Workshop Manual Download Page 6

Page: 6 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

Steering column switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

7.1

Steering column switch- vehicles up to CW 21/10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

7.2

Steering column switch- vehicles as of CW 22/10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

7.3

Setting middle position of the return ring with coil spring . . . . . . . . . . . . . . . . . . . . . . . . . . 144

Steering lock with ignition starter switch and lock cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 145

8.1

Removing and installing lock cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

8.2

Removing and installing steering lock - vehicles up to CW 21/10 . . . . . . . . . . . . . . . . . . . . 146

8.3

Removing and installing steering lock - vehicles as of CW 22/10 . . . . . . . . . . . . . . . . . . . . 146

8.4

Removing and installing ignition/starter switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

8.5

Removing and installing ignition key anti-removal lock solenoid N376 . . . . . . . . . . . . . . . . 148

8.6

Contact assignment on the ignition/starter switch and the ignition key anti-removal lock . . 149

Parking aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

9.1

Summary of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

9.2

Removing and installing the parking aid control unit J446 . . . . . . . . . . . . . . . . . . . . . . . . 151

9.3

Removing and installing the rear parking aid warning buzzer H15 . . . . . . . . . . . . . . . . . . 152

9.4

Remove and install the front parking aid warning buzzer H22 . . . . . . . . . . . . . . . . . . . . . . 152

9.5

Removing and installing parking aid senders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

9.6

Parking aid sender holder - making holes, assignment, fitting location, glueing procedure

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

9.7

Self-diagnosis of the parking aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

Door entry lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156

10.1 Door entry lighting in the exterior mirror - vehicles up to MY 08 . . . . . . . . . . . . . . . . . . . . 156

10.2 Door entry lighting in the exterior mirror - vehicles as of MY 09 . . . . . . . . . . . . . . . . . . . . . . 156
11

Registration number lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158

11.1 Removing and installing licence plate carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158

96 - Lights, bulbs, switches - interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

1.1

Removing and installing glove box light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

1.2

Removing and installing door warning lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

1.3

Removing and installing luggage compartment light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160

1.4

Removing and installing the front and rear interior light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160

1.5

Removing and installing the interior light with sliding roof switch . . . . . . . . . . . . . . . . . . . . 161

1.6

Removing and installing the sliding roof switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161

Interior switches, in the dash panel, the centre console and the doors . . . . . . . . . . . . . . . . 162

2.1

Removing and installing light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

2.2

Removing and installing the headlight range control adjuster . . . . . . . . . . . . . . . . . . . . . . 162

2.3

Removing and installing switches in centre console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

2.4

Removing and installing hazard warning lights button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

2.5

Removing and installing the mirror adjustment switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164

2.6

Removing and installing the switch for the power window lifter . . . . . . . . . . . . . . . . . . . . . . 164

2.7

Removing and installing interior monitoring deactivation switch E 267 and deactivation button

for vehicle inclination sender E 360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166

2.8

Removing and installing switch for inside actuation of the central locking . . . . . . . . . . . . . . 166

2.9

Removing and installing the fuel selector switch E395 (petrol/gas) . . . . . . . . . . . . . . . . . . 166

2.10 Removing and installing the rear seat heating switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
3

Components in the luggage compartment and tailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

3.1

Removing and installing the switch for the luggage compartment lighting . . . . . . . . . . . . . . 168

3.2

Removing and installing the motor for unlocking the tailgate . . . . . . . . . . . . . . . . . . . . . . . . 168

3.3

Removing and installing the tailgate release switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

4.1

Removing and installing horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

Anti-theft warning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170

5.1

General points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170

5.2

Removing and installing the horn H12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

Contents

Summary of Contents for Octavia II 2004












































































































































































































Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands

Skoda Octavia II 2004, Workshop Manual

Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands