Skoda Octavia II 2004 Workshop Manual Download Page 87

Page: 87 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

Connection for external audio sour‐

ces - R199- (AUX)

This is designed to connect the audio signal from the external

stereo systems and to play back music from these systems via

the radio/navigation installed ex works.
Contact assignment of plug connection and current flow diagram

⇒ Current flow diagrams, Electrical fault finding and Fitting loca‐

tions.
Description of the function and additional information:
♦ ⇒ Owner's manual Octavia II
♦ ⇒ Operating instruction of the radio/navigation system

⇒ “9.1 Removing and installing connection for external audio

sources R199 (AUX)”, page 79

9.1

Removing and installing connection for

external audio sources - R199- (AUX)

Removing
– Switch off the radio/navigation, all electrical consumers and

take out the ignition key.

– Remove the centre console between driver and front passen‐

ger ⇒ Body Work; Rep. gr. 68 .

– Disconnect plug.
– Press together the retaining tabs -arrows- and push connec‐

tion for external audio sources -1- out of the centre console

-2-.

Installing
The installation occurs in reverse order.

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

9. Connection for external audio sources R199 (AUX)

Summary of Contents for Octavia II 2004












































































































































































































Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands

Skoda Octavia II 2004, Workshop Manual

Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands