Skoda Octavia II 2004 Workshop Manual Download Page 200

Page: 200 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

2.3.2

Removing and installing

Note

♦

If the data bus diagnostic interface Gateway - J533- is re‐

placed, it must be connected before the removal ⇒ Vehicle

diagnostic tester and the function “replace data bus diagnostic

interface” must be selected in the targeted fault finding for

reading the codes stored in the control unit.

♦

If the original data bus diagnostic interface Gateway - J533- is

not available or does not communicate with the diagnostic unit,

then proceed according to the information in the ⇒ Vehicle di‐

agnostic tester.

♦

The coding can also be performed on-line (network connec‐

tion).

Remove - left-hand drive
The data bus diagnostic interface Gateway - J533- is located on

the strut above the brake pedal.
– Switch off the ignition and all electrical consumers!
– Remove lower part of the dash panel insert on the driver's side

⇒ Body; Rep. gr. 70 Work.

– Unlock -arrows- control unit -1- and remove from control panel

holder.

– Disconnect plug connection -2-.
Remove - right-hand drive
The data bus diagnostic interface Gateway - J533- is located

above the onboard supply control unit - J519- at the rear.
– Removing the dash panel ⇒ Body Work; Rep. gr. 70 .

– Disconnect plug connection -3-.
– Press off the catch peg -arrow A- and push out -arrow B- the

diagnostic interface -1- from the bracket -2-.

Installing
The installation occurs in reverse order.

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

192

Rep. gr.97 - Wiring

Summary of Contents for Octavia II 2004












































































































































































































Search results

Summary of Contents for Octavia II 2004

Reviews:

Brands by name

Popular brands

Skoda Octavia II 2004, Workshop Manual

Search results

Summary of Contents for Octavia II 2004

Reviews:

Brands by name

Popular brands