manualshive.com logo in svg

Skoda Octavia II 2004, Workshop Manual

The Skoda Octavia II 2004 Workshop Manual is a comprehensive guide for owners and enthusiasts of this remarkable vehicle. This manual provides detailed instructions, diagrams, and specifications to help with repairs, maintenance, and troubleshooting. It is available for free download from manualshive.com, ensuring easy and convenient access to this valuable resource.

Share
Download
background image

 

 

 

 

 

 

 

 

 

 

 

 

 

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 

unless authorised by 

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability 

with respect to the correctness of information in this document. Copyright by 

ŠKODA AUTO A. S.

�

 

– Press the catch -arrow A- and fold down the cover with the

performance module for the headlight -1- while taking into ac‐

count the connected cable lengths.

– Disconnect plug connection -1-.
– Release the wire spring clamp -2- and remove the light bulb.
– The installation occurs in reverse order.

2.3.5

Replacing bulb for turn signal light

PY21W

– Remove headlight 

⇒ page 99

 .

– Remove bulb socket -1- by turning in the direction of the arrow

“OPEN”.

– Remove the bulb from the socket.
– The installation occurs in reverse order.

2.3.6

Replacing bulb W5W/W5W BL for the

parking light

– Remove headlight 

⇒ page 99

 .

– Press the catches -arrows B- and remove the headlight cover

-3- with the control unit for gas discharge lamp -2- while taking

into account the connected cable lengths and fold down.

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

116

     Rep. gr.94 - Lights, bulbs, switches - exterior

Summary of Contents for Octavia II 2004












































































































































































































Reviews:

No comments

Related manuals for Octavia II 2004

Zamil CX SERIES Installation, Operation & Maintenance Manual preview
CX SERIES
Brand: Zamil Pages: 20
Bard QA241D Installation Instructions Manual preview
QA241D
Brand: Bard Pages: 33
Audi 1999 TT Repair Manual preview
1999 TT
Brand: Audi Pages: 199
Heat Controller VMH30SB-1 Owner'S Manual preview
VMH30SB-1
Brand: Heat Controller Pages: 19
Daikin RXL25M2V1B Installation Manual preview
RXL25M2V1B
Brand: Daikin Pages: 18
Hisense AVS-07URCSABA Operation Installation Maintenance Manual preview
AVS-07URCSABA
Brand: Hisense Pages: 31
teca 0-3070-2-016 Product Information Packet preview
0-3070-2-016
Brand: teca Pages: 11
Omega OTEC IEFC-D Series Installation Manual preview
OTEC IEFC-D Series
Brand: Omega Pages: 12
York ECO R-407C User Manual preview
ECO R-407C
Brand: York Pages: 44
HEIL PGD4 Owner'S Manual preview
PGD4
Brand: HEIL Pages: 10
Olimpia splendid Maestro Smart Instructions For Installation, Use And Maintenance Manual preview
Maestro Smart
Brand: Olimpia splendid Pages: 40
Aeroex ARO-400 Installation & Service Manual preview
ARO-400
Brand: Aeroex Pages: 12
Daikin 2AMX40F2V1B Installation Manual preview
2AMX40F2V1B
Brand: Daikin Pages: 19
Hawk AS 500 HEPA Quick Start Manual preview
AS 500 HEPA
Brand: Hawk Pages: 2
Carrier 42NQV050M Series Service Manual preview
42NQV050M Series
Brand: Carrier Pages: 102
Carrier 38MC 207-334 Installation, Operation And Maintenance Instructions preview
38MC 207-334
Brand: Carrier Pages: 44
Acson ACC 10C Technical Manual preview
ACC 10C
Brand: Acson Pages: 203
Carrier 40MPHA Service Manual preview
40MPHA
Brand: Carrier Pages: 68

Brands by name

Popular brands

Load more brands