Skoda Octavia II 2004 Workshop Manual Download Page 169

Page: 169 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

1.5

Removing and installing the interior light

with sliding roof switch

Removing
– Switch off the ignition and all electrical consumers!
– Carefully remove front lens -arrow- downwards.

– Release screws - 1 - (2 Nm).
– Remove the interior light downwards and disconnect the plug

connections.

Note

It is necessary to not remove the interior light to replace the light

bulb.

2 - Light bulb without base W5W
3 - Soffitte C10W
Installing
– Fit together the plug connections.
– Insert interior light with sliding roof switch and secure with the

two cross-head screws (1.5 Nm).

– First of all insert lens with the catch lugs in the interior light

slots and then press upwards to the noticeable latching.

1.6

Removing and installing the sliding roof

switch

Removing
– Remove front interior light with sliding roof switch

⇒ page 161

– Press off pegs -arrows- and remove sliding roof switch from

the illumination housing.

Installing
The installation occurs in reverse order.

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

1. Interior Lights

161

Summary of Contents for Octavia II 2004












































































































































































































Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands

Skoda Octavia II 2004, Workshop Manual

Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands