Skoda Octavia II 2004 Workshop Manual Download Page 116

Page: 116 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

Headlights with Xenon discharge

lamps

WARNING

Mortal high voltage, risk of injury and risk of pollution.
Observe use and safety instructions for gas discharge lamps

⇒ Electrical System – general notes; Rep. gr. 94 .
H1 bulbs are pressurized and can burst when changing the

bulb. It is recommended to wear gloves and safety glasses

when changing bulbs.

Note

♦

Do not touch the glass when installing the light bulb. Your fin‐

gers will leave traces of grease on the glass which then

evaporate when the bulb is switched on causing it to cloud.

♦

Pay attention to the correct fitting and undamaged seals on

the plastic covers as well as the correct positioning of the cov‐

er. Water ingress destroys the headlight.

♦

When handling a fault it is absolutely essential to know the

function and operation of the illumination system.

♦

Additional information:

⇒ Owner's manual Octavia II
⇒ Current flow diagrams, Electrical fault finding and Fitting loca‐

tions

⇒ “2.1 Fault recognition and fault display”, page 108
⇒ “2.2 Headlight with Xenon discharge lamps- vehicles up to MY

08”, page 109
⇒ “2.3 Headlights with Xenon discharge lamps and cornering light

- vehicles as of MY 09”, page 113
⇒ “2.4 Removing and installing control unit for headlight range

control J431 or cornering light and headlight range control unit

J745 ”, page 118
⇒ “2.5 Removing and installing vehicle level sensor G78 front left

or G76 rear left ”, page 118
⇒ “2.6 Contact assignment of plug connection for control unit for

headlight range control J431 or cornering light and headlight

range control unit J745 ”, page 119

2.1

Fault recognition and fault display

In case of malfunctions of the headlight range control or the AFS

system (Adaptive Frontlighting System) the warning light “light

failure” lights up.
The automatic headlight range control (vehicles as of MY 09) and

the onboard supply control unit are equipped with the self-diag‐

nosis that facilitates the fault finding of the headlights.
For fault finding use the ⇒ Vehicle diagnostic tester in the function

“Targeted fault finding”.

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

108

Rep. gr.94 - Lights, bulbs, switches - exterior

Summary of Contents for Octavia II 2004












































































































































































































Search results

Summary of Contents for Octavia II 2004

Reviews:

Brands by name

Popular brands

Skoda Octavia II 2004, Workshop Manual

Search results

Summary of Contents for Octavia II 2004

Reviews:

Brands by name

Popular brands