Skoda Octavia II 2004 Workshop Manual Download Page 159

Page: 159 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

1 - Rear parking aid sender

❑ below the protective

strip of the rear shock

absorber

❑ Removing and installing

⇒ page 153

2 - Control unit for the parking

aid - J446-

❑ behind the left luggage

compartment trim panel

❑ Removing and installing

⇒ page 151

3 - Rear parking aid warning

buzzer - H15-

❑ in the trim panel of pillar

❑ Removing and installing

⇒ page 152

4 - Front parking aid sender

❑ below the protective

strip of the front shock

absorber

❑ Removing and installing

⇒ page 153

5 - The warning buzzer for the

front parking aid - H22-

❑ behind the right dash

panel insert

❑ Removing and installing

⇒ page 152

❑ installed in vehicles as

of MY 09

9.2

Removing and installing the parking aid

control unit - J446-

Removing
– Switch off the ignition and all electrical consumers!
– Remove right side trim panel in luggage compartment ⇒ Body

Work; Rep. gr. 70 .

– Release and disconnect the plug connections.
– Release nuts -arrows- (1.5 Nm) and take out parking aid con‐

trol unit.

Installing
Installation is carried out in the reverse order. When installing,

observe the following:
– When replacing, code the new parking aid control unit - J446-

⇒ Vehicle diagnostic tester.

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

9. Parking aid

151

Summary of Contents for Octavia II 2004












































































































































































































Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands

Skoda Octavia II 2004, Workshop Manual

Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands