Skoda Octavia II 2004 Workshop Manual Download Page 47

Page: 47 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

– Press the pre-selection button “CD TRANS” - fig. - in this dis‐

play, in order to send the command for switching off the drive.

A gong may come from the speakers which confirms that the

command has been sent.

– Afterwards, press the button “BACK” button -fig-.

– Once again “SYSTEM DEBUG” -fig-. appears in the display

by operating the button “BACK”

– The radio goes back to the standard display of the FM station

after approx. 10 seconds, see the -first illustration- (this display

can differ depending on the stored pre-selections).

– Switch off the radio with the rotary knob. The drive is switched

off, when everything was carried out correctly.

We recommend to listen carefully to the drive, as similar noises

can be heard when switching off the CD drive as for the CD

changer.
– The radio is ready to be taken out when all noises are elimi‐

nated.

Note

All radios “AUDIENCE” are supplied as replacement part with CD

drive in the deactivated state. When connecting the radio to the

vehicle voltage the drive is automatically initialised when pressing

the rotary knob for the first time. Therefore the operating mode

cannot be activated.

1.6

Self-diagnostic function of radio system

Carry out “self-diagnosis” with the ⇒ Vehicle diagnostic tester in

the function “Targeted fault finding”.

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

1. Radio

Summary of Contents for Octavia II 2004












































































































































































































Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands

Skoda Octavia II 2004, Workshop Manual

Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands