Skoda Octavia II 2004 Workshop Manual Download Page 3

Page: 3 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

Contents

27 - Starter, current supply, CCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contact corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1

Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2

Warning instructions and safety precautions when working on the battery . . . . . . . . . . . .

2.3

Work sequence when disconnecting and connecting the battery . . . . . . . . . . . . . . . . . . . .

2.4

Checking battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5

Charging battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6

Removing and installing battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.7

Removing and installing the battery tray in the engine compartment . . . . . . . . . . . . . . . . . .

2.8

Battery parameterisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Battery types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1

Battery with a magic eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2

Fleece battery (AGM battery) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.1

Removing and installing starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.1

Checking generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.2

Removing and installing alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.3

Fixing the B+ wire to the AC generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.4

Checking the carbon brushes of the AC generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.5

Removing and installing the Bosch voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.6

Removing and installing the Valeo voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.7

Removing and installing V-ribbed belt pulley on alternator . . . . . . . . . . . . . . . . . . . . . . . . 15

5.8

Removing and installing the V-ribbed belt pulley with free wheel . . . . . . . . . . . . . . . . . . . . 15

Removing and installing the cruise control (CC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

“Start-stop” system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

7.1

Safety precautions for vehicles with “start-stop” system . . . . . . . . . . . . . . . . . . . . . . . . . . 17

7.2

General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

7.3

Fault recognition and fault display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

7.4

Battery recharging or starting by external source on vehicles with “start-stop system” . .

7.5

Replacing the battery on vehicles with “start-stop” system . . . . . . . . . . . . . . . . . . . . . . . . 18

7.6

Voltage stabiliser J532 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

7.7

Battery monitor control unit J367 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

7.8

Button for “start-stop” system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

90 - Gauges, instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Dash panel insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

1.1

Adjust/replace dash panel insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

1.2

Removing and installing the dash panel insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

1.3

Relacing shield with transparent washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

1.4

Warning light symbols in dash panel insert - vehicles up to MY 08 . . . . . . . . . . . . . . . . . . 25

1.5

Warning light symbols in dash panel insert - vehicles as of MY 09 . . . . . . . . . . . . . . . . . . 26

1.6

Service interval display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

The self-diagnostic function of the dash panel insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

91 - Radio, telephone, navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

1.1

General Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

1.2

Electronic anti-theft coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

1.3

Overview of radio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

1.4

Plug connections on the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

Contents

Summary of Contents for Octavia II 2004












































































































































































































Search results

Summary of Contents for Octavia II 2004

Reviews:

Brands by name

Popular brands

Skoda Octavia II 2004, Workshop Manual

Search results

Summary of Contents for Octavia II 2004

Reviews:

Brands by name

Popular brands