Skoda Octavia II 2004 Workshop Manual Download Page 16

Page: 16 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

Battery types

⇒ “3.1 Battery with a magic eye”, page 8
⇒ “3.2 Fleece battery (AGM battery)”, page 8

3.1

Battery with a magic eye

Located in the engine compartment.
All notes and comments to this chapter can be found in the Work‐

shop Manual ⇒ Electrical system - General notes ⇒ Electrical

system - General notes; Rep. gr. 27 .

Note

♦

A battery with a magic eye with EFB technology (Enhanced

Flooded Battery) can also be fitted in vehicles with petrol en‐

gines and with start-stop system. It is fitted with thicker plates

and separators with special polyester scrim. Thereby the cycle

durability as well as the loading capacity are considerably in‐

creased in order to recover the energy more quickly while

driving.

♦

Maintenance and checks on these batteries are the same as

on batteries with a magic eye.

3.2

Fleece battery (AGM battery)

All notes and comments to this chapter can be found in the Work‐

shop Manual ⇒ Electrical system - General notes ⇒ Electrical

system - General notes; Rep. gr. 27 .

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

Rep. gr.27 - Starter, current supply, CCS

Summary of Contents for Octavia II 2004












































































































































































































Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands

Skoda Octavia II 2004, Workshop Manual

Search results

Summary of Contents for Octavia II 2004

Reviews:

Related manuals for Octavia II 2004

Brands by name

Popular brands