manualshive.com logo in svg

Siemens SITRANS F TRANSMAG 2, Operating Instructions Manual, Page: 3 / 126

Share
Download
Siemens SITRANS F TRANSMAG 2 Operating Instructions Manual Download Page 3

Table of contents

1

Introduction ........................................................................................................................................... 7

1.1

Purpose of this documentation ............................................................................................ 7

1.2

History................................................................................................................................. 7

1.3

Checking the consignment................................................................................................... 7

1.4

Items supplied ..................................................................................................................... 8

1.5

Designated use .................................................................................................................... 8

1.6

Security information ............................................................................................................ 8

1.7

Transportation and storage .................................................................................................. 9

1.8

Notes on warranty ............................................................................................................... 9

2

Safety notes ......................................................................................................................................... 11

2.1

General safety instructions................................................................................................. 11

2.2

Laws and directives............................................................................................................ 11

2.3

Use in hazardous areas....................................................................................................... 13

3

Description........................................................................................................................................... 15

3.1

Overview ........................................................................................................................... 15

3.2

Features ............................................................................................................................ 15

3.3

BUS Communication .......................................................................................................... 16

3.4

Theory of operation ........................................................................................................... 17

3.5

Operating principle ............................................................................................................ 18

4

Installing/mounting ............................................................................................................................. 19

4.1

Installation safety precautions............................................................................................ 19

4.2

Sensor installation ............................................................................................................. 19

4.2.1

Determining a location....................................................................................................... 19

4.2.2

Orienting the sensor .......................................................................................................... 22

4.2.3

Removing the liner protectors ............................................................................................ 23

4.2.4

Mounting .......................................................................................................................... 24

4.2.5

Potential equalization......................................................................................................... 27

4.2.6

Installation with grounding rings........................................................................................ 28

4.3

Transmitter installation ...................................................................................................... 30

4.3.1

Standard wall-mounting bracket......................................................................................... 30

4.3.2

Pipe or wall mounting with special wall-mounting bracket.................................................. 30

4.4

Turning the local display..................................................................................................... 32

5

Connecting .......................................................................................................................................... 33

5.1

General Information........................................................................................................... 33

TRANSMAG 2 with MAG 911/E
Operating Instructions, 03/2021, A5E00102775-AC

3

Summary of Contents for SITRANS F TRANSMAG 2































































































































Reviews:

No comments