manualshive.com logo in svg

Siemens SITRANS F TRANSMAG 2, Operating Instructions Manual, Page: 27 / 126

Share
Download
Siemens SITRANS F TRANSMAG 2 Operating Instructions Manual Download Page 27

Torque calculations
All values are theoretical and are calculated on the assumption that:

• All bolts are new and material selection is according to EN 1515-1 table 2.

• Gasket material not exceeding 75 shore A is used between the flowmeter and mating flanges.

• All bolts are galvanized and adequately lubricated.

• Flanges are made of carbon steel.

• Flowmeter and mating flanges are correctly aligned.

4.2.5

Potential equalization

To obtain optimum results from the measuring system, the sensor must have the same electrical 
potential as the liquid being measured.

This is achieved by means of built-in grounding electrodes.

Figure 4-16

Potential equalization with earthing electrodes   

Cathodic protected piping

Special attention must be paid to systems with cathodic protection.   

WARNING

Use in hazardous area!

Cathodic pipe protection is not allowed in hazardous areas

Installing/mounting

4.2 Sensor installation

TRANSMAG 2 with MAG 911/E
Operating Instructions, 03/2021, A5E00102775-AC

27

Summary of Contents for SITRANS F TRANSMAG 2































































































































Reviews:

No comments