manualshive.com logo in svg

Siemens SITRANS F TRANSMAG 2, Operating Instructions Manual, Page: 77 / 126

Share
Download
Siemens SITRANS F TRANSMAG 2 Operating Instructions Manual Download Page 77

Service and Maintenance

9

9.1

Maintenance

The device is maintenance-free. However, a periodic inspection according to pertinent directives 
and regulations must be carried out.   

An inspection can include check of:

• Ambient conditions

• Seal integrity of the process connections, cable entries, and cover screws

• Reliability of power supply, lightning protection, and grounds

NOTICE
Repair and service must be carried out by Siemens authorized personnel only.

Note

Siemens defines flow sensors as non-repairable products. 

Cleaning the enclosure

• Clean the outside of the enclosure with the inscriptions and the display window using a cloth 

moistened with water or a mild detergent.

• Do not use any aggressive cleansing agents or solvents, e.g. acetone. Plastic parts or the 

painted surface could be damaged. The inscriptions could become unreadable.

Enclose the bill of lading, return document and decontamination certificate in a clear plastic 
pouch and attach it firmly to the outside of the packaging.

TRANSMAG 2 with MAG 911/E
Operating Instructions, 03/2021, A5E00102775-AC

77

Summary of Contents for SITRANS F TRANSMAG 2































































































































Reviews:

No comments